WATstop - Цементный водонепроницаемый продукт

Multipurpose epoxy-cement waterproofing coating.‎ It is formulated with a special epoxy resin (Part A), a catalyst (Part B) and special cement (Part C).‎ ADVANTAGES • do-it-yourself (in cases of mild humidity in foundation) • Multipurpose • resistant up to 9,5 atM of negative counterthrust pressure • resistant up to 9,5 atM atm of positive pressure • adhesion on any kinds of surface USES • It acts as an osmotic cement when used to restore humid walls, as an anti-salt barrier in the dehumidification system (consult our technical office for information on the anti-humidity system).‎ • It acts as waterproofing coating to eliminate water infiltration both with negative counterthrust (up to 3 atm of pressure) and with positive pressure, to seal canalisations, elevators pits and floors.‎ • To prevent rising damp on the external walls in contact with pavements, garages, etc.‎ • To waterproof underground foundations and floors with a high level of humidity.‎ APPLICATION MORTAR SETTING The surface must to be prepared in a correct way.‎ The base must be solid, mechanically resistant, perfectly clean, dry on surface and without fragmented parts.‎ In the case of new cement base, this must be fully set and stable.‎ Old clay or marble-chip floor tile floorings, must be attached to the base without traces of substances such as oils, wax, etc.‎ Remove the three components from the bucket: 1.‎ Open the epoxy mortar and pour it into the bucket.‎ 2.‎ Open the cement, pour it into the bucket and mix it.‎ 3.‎ Open the catalyst, pour it into the bucket and mix all the paste perfectly.‎ 4.‎ Add water in the amount of: 20% of WETstop’s if applied by brush.‎ 40% of WETstop’s if applied by paint brush.‎ APPLICATION AS ANTI-SALT OSMOTIC CEMENT 1.‎ The surface to treat must be at least 70 cm above the highest humidity line.‎ 2.‎ Prepare the surface, eliminating old paint, fragmented parts, grease, oils, chemical products, cement flakes.‎ In case of fragmented surface you must take the flash off till obtain a suitable base.‎ 3.‎ Before applying WETstop, wet the surface with a sponge soaked in water to remove the dust.‎ Apply with brush a WETstop coat, being sure to totally cover the surface.‎ Apply, if necessary, a cement smoother as putty.‎ 4.‎ Paint the surface 48 hours after the smoother application.‎ 5.‎ Apply WETstop as waterproofing coating for barthrooms, showers, basins.‎ Tiles can be glued directly onto WETstop within 2 days.‎ TECHNICAL DATA Aspect Black semi-liquid Waterproofing 9.‎5 ATM UNI EN 12039-8) 9,5 ATM with counterthrust Resistance to salt Optimal Resistance to solvents Not resistant Resistance to organic acids Not resistant Resistance to inorganic acids with 5% concentration Not good Application temperature +5°C / +35°C Paste lasting 2 hours at 20°C Resistance to weathering test 2 000 hours withou remarkable changes After 50 cycles freezing/defrosting (-15°C/+15°C) (UNI EN 202) Inaltered YIELD kg/mq 1-1,2 as anti-salt osmotic.‎ kg/mq 2-2,5 as waterproofing with a negative counterthrust.‎ PACKAGING Metal can of kg 5.‎ Plastic pail of kg 7 and kg 13.‎ STORAGE Store the product in the dark in temperatures between 5°C and +35°C.‎ Use by: 12 months.‎ Further info from manufacturer on WATstop DIASEN